Products
Home > Products > Gasket and Washer Cutters

Products

We have now probably the most innovative production equipment, experienced and qualified engineers and workers, regarded high quality control systems and also a friendly expert income team pre/after-sales support for Gasket and Washer Cutters, For even more inquires make sure you will not wait to make contact with us. Thank you - Your help continuously inspires us.
Gasket and Washer Cutters, Many items fully conform to the most rigorous of international guidelines and with our first-rate delivery service you will have them delivered at any time and in any place. And because Kayo deals in the entire spectrum of protective equipment, our customers don't ought to waste time shopping around.

Related Products

Hot Products

  • Packing Cutting Knife

    Packing Cutting Knife

    Packing cutting knife has a fine bevelled blade to cut braided packings, and a serrated blade to cut molded items.
  • Gasket Punch Set

    Gasket Punch Set

    Gasket Punch Set 6mm - 38mm*16's punching dies and table. Used for punching holes in soft brass copper and other soft metals as well as leather canvas and gasketing materials. The set is composed of 16 punching dies ranging in size from 6 to 38mm diameter.
  • Injection Gun

    Injection Gun

    Injection gun utilizes a button-head or flow-through fitting which is permanently installed on the pump or valve stuffing box.
  • Hand Cutter For Soft Gaskets

    Hand Cutter For Soft Gaskets

    Hand Cutter For Soft Gaskets is perfect to use on project site. Easy to use, and cut any soft material gasket like rubber gasket, asbestos, non-asbestos gasket, PTFE gasket, graphite gasket and SS reinforced graphite gasket.
  • Multi Angle Anvill Cutter For Gasket and Trim

    Multi Angle Anvill Cutter For Gasket and Trim

    Multi Angle Anvill Cutter For Gasket and Trim: Easy To Use Xpert Mitre Shears, Great Tool For Glazer Cuts Through Trims, Upvc Gasket, Conduit, Beading, Plastic Pipe and Picture Moldings
  • Guillotine Packing Cutter

    Guillotine Packing Cutter

    Guillotine Packing Cutter permits accurate cutting of rings from spiral or flat coil packings. The scale reads directly in terms of shaft sizes. In inches and in millimeters.
  • Related Blog
  • Reviews

  • Spiral wound gasket production process and equipment

    In the present seal, metal spiral wound gasket with excellent elasticity, high temperature, high pressure,low temperature and other characteristics, has become a very wide range of applied seal. Especially suitable for uneven loading, relaxation and easy access together, cyclical changes in temperature and pressure of the occasion, is the main flange gasket. In the petrochemical pipelines, mechanicalseals,shipbuilding,metallurgy, aerospace and other industries widely.

  • Installing Grafoil Crinkle Gasket Tape

    1. Brush off any rust or foreign particles. Wipe flange surface thoroughly with a rag soaked in acetone or other suitable solvent to remove grease or oil. 2. Insert fingernail between the paper backing strip and the tape and strip the paper back three to six inches. Draw a reference line in flange and press squared off end of tape against it. 3. Now, start laying the tape along the face of the flange, peeling the paper backing as you go. To prevent the adhesive surfaces of the tape from doubling back on themselves and sticking together, strip away only a few inches of paper at a time.

  • Effecting a Seal

    A seal is affected by compressing the gasket material and causing it to flow into the imperfections on the gasket seating surfaces so that intimate contact is made between the gasket and the gasket seating surfaces preventing the escape of the confined fluid. Basically there are four different methods that may be used either singly or in combination to achieve this unbroken barrier.

  • Gasket Seating

    There are two major factors to be considered with regard to gasket seating. The first is the gasket material itself. The ASME Unfired Pressure Vessel Code Section VIII, Division 1 defines minimum design seating stresses for variety of gasket materials.

  • How to Cut Gasket material?

    Clean radius and straight cuts are achievable on gasket material with the proper tooling. Thinner types of gasket material require nothing more than sharp blades and hollow gasket cutters. Gasket material over 1/4-inch thick require specialized mechanical tools to create the precision cuts necessary to seal a piece of equipment and is best left to professionals. Properly securing the gasket material and ensuring the tools used are in good condition will allow you to cut thinner gasket material efficiently and precisely.

  • Braiding Machine Ship to Poland

    More than 10 sets of braiding machines will be shipped to Poland within this week.

Send Inquiry